Sta-Set X Plus

Parallel Core


PRODUCT DESCRIPTION:

Sta-Set X Plus is constructed using New England Ropes patented parallel core design, using Vectran & Polypropylene fibers contained within a helically wrapped polyester tape and covered by a braided jacket of filament polyester. This construction creates a rope that is lighter weight and lower stretch than a similar 100% polyester ropes.

FEATURES:

APPLICATIONS:

TECHNICAL SPECIFICATIONS:

STRENGTH / WEIGHT
Product Code
(White)
Diameter Weight
(Lbs/100 ft.)
Tensile
(Lbs.)
Inches mm
3050-05 3/16" 5mm 1.2 1,600
3050-06 1/4 " 6mm 1.6 2,700
3050-08 5/16" 8mm 2.7 4,400
3050-10 3/8 " 10mm 4.2 5,500
3050-11 7/16" 11mm 5.4 7,500
3050-12 1/2 " 12mm 6.5 9,600
3050-14 9/16" 14mm 8.9 1,300

Compliance to the above specifications is based upon testing according to the Cordage Institute Standard Testing Methods for Fiber Rope and/or ASTM D-4268 Standard Methods of Testing Fiber Ropes.
Weights - Are average and may vary +/- 5%
Tensile strengths - Are approximate average for new, unused ropes. To estimate the minimum tensile strength of a new rope, reduce the approximate average by 15% (Cordage Institute defines minimum tensile strength as two standard deviations below the average tensile strength of the rope).

WORKING ELONGATION

SUNLIGHT/UV:

Very little degradation from UV. Can be used outside over long term if inspected regularly.

CHEMICALS:

Good resistance to most minerals / organics, acids, weak alkalis, bleaches and other oxidizing agents and most solvents.

HEAT:

Melting point of Polyester 480F, Polypropylene 330F
Vectran melting point 625F, progressive strength loss above 430F

DIELECTRICS:

Good resistance to the passage of electrical current. However in rope form, dirt, surface contaminants, water entrapment and the like can significantly affect dielectric properties. Extreme caution should be exercise any time a rope is in the proximity of live circuits.

SHEAVES:

Recommended D/d ratio is 8:1

WORKING LOADS:

No blanket working load recommendation can be made because it depends on the application and conditions of use, especially potential danger to personnel. It is recommended that the user establish working loads and safety factors based on professional and experienced assessments of risks. The working load is a guideline for the use of a rope in good condition for non-critical applications and should be reduced where life, limb, or valuable property is involved. Or exceptional service such as shock, sustained loading, severe vibration, etc. The Cordage Institute specifies that the Safe Working Load of a rope shall be determined by dividing the Minimum Tensile Strength by the Safety Factor. Safety factors range from 5 to 12 for non-critical uses, 15 for life lines.

SLK= Minimum Break Strength / Safety Factor

COATING:

Can be Urethane coated to improve abrasion resistance, UV resistance, to crate a water barrier and to provide color coding.

SPECIFIC GRAVITY:

COLOR:

White, Red, Green, Blue, Black. ("X" red & orange tracer)
Sta-Set X Plus

QUALITY ASSURANCE:

STANDARD LENGTH:

600 ft

SPLICING INSTRUCTIONS:

Parallel Core Eye Splice

FABRICATION SERVICES:

Fabricated Units can be provides including splices, thimbles, integral chafe sleeves, etc. Contact Customer Service for details.

COMPLIMENTARY PRODUCTS:

PART NUMBER SERIES:

3050 - White
3051 - Red
3052 - Green
3053 - Blue
3054 - Black

 

  Rope Products Hm.
262 SW 33rd Street
Fort Lauderdale FL  33315
Tel 888-596-7673
Tel (954) 525-6575
Fax (954) 525-5887