High Performance, Strength, and Durability!
Rope, inc. introduces Endura Braid by New England Ropes, the latest double braid high tech rope using Ultra High Molecular Weight Polyethylene (UHMWPE). This double braided construction consists of an Endura 12 core and a durable, twill polyester cover for increased abrasion resistance and better handling. The core is vinyl coated to increase durability.
Contact Us for more information and ordering this in-stock item.
- Excellent Strength-to-Size Ratio
- Ultra Low Elongation
- Low Weight
- Easily spliced
- Excellent flexibility
- Excellent Wet/Dry Strength Retention
- Low stretch control lines
- Slings/Hoisting Ropes
Compliance to the above specifications is based upon testing according to the Cordage Institute Standard Testing Methods for Fiber Rope and/or ASTM D-4268 Standard Methods of Testing Fiber Ropes.
STRENGTH / WEIGHT Product Code
Inches mm 2530-05 3/16 " 5 1.00 2,250 2530-06 1/4 " 6 1.70 4,000 2530-08 5/16 " 8 2.70 7,000 2530-10 3/8 " 10 3.90 10,000 2530-11 7/16 " 11 5.30 14,000 2530-12 1/2 " 12 6.90 19,000 2530-14 9/16 " 14 8.80 25,200 2530-16 5/8 " 16 10.80 33,000 2530-24 3/4 " 18 15.70 37,400 2530-28 7/8 " 22 20.0 53,000 2530-32 1 " 25 26.0 70,800 2530-36 1-1/8 " 28 35.3 98,600
Weights - Are average and may vary +/- 5%
Tensile strengths: Are approximate average for new, unused ropes. To estimate the minimum tensile strength of a new rope, reduce the approximate average by 10% (Cordage Institute defines minimum tensile strength as two standard deviations below the average tensile strength of the rope).
CHEMICALS:Good resistance to most minerals/organics, acids, and weak alkalis. Excellent resistance to bleaches and other oxidizing agents and to most solvents.
SUNLIGHT/UV:Very little degradation from UV. Can be used outside over long term if inspected regularly.
HEAT:Melting point of Polyester is 480°F with progressive strength loss above 300°F.
Melting point of UHMWPE is 300°F with progressive strength loss above 150°F.
DIELECTRICS:Polyester and the UHMWPE core fiber have good resistance to the passage of electrical current. However, dirt, surface contaminants, water entrapment, and the like can significantly affect dielectric properties. Extreme caution should be exercise any time a rope is in the proximity of live circuits.
SHEAVES:Recommended D/d* ratio is 8:1
(* Sheave Diameter to Rope Diameter)
COATING:Proprietary coating to improve abrasion resistance, UV resistance, and to create a water barrier.
COLORS:White, Red Fleck, Green Fleck, & Blue Fleck
NEW COLORS: Solid Red, Solid Blue, & Solid Green
All Endura braids are identified by a fine red and black tracer and a distinctive check pattern in both fleck and solid colors.
WORKING LOADS:No blanket working load recommendation can be made because it depends on the application and conditions of use, especially potential danger to personnel. It is recommended that the user establish working loads and safety factors based on professional and experienced assessments of risks. The working load is a guideline for the use of a rope in good condition for non-critical applications and should be reduced where life, limb, or valuable property is involved. Or exceptional service such as shock, sustained loading, severe vibration, etc. The Cordage Institute specifies that the Safe Working Load of a rope shall be determined by dividing the Minimum Tensile Strength by the Safety Factor. Safety factors range from 5 to 12 for non-critical uses, 15 for life lines.
SLK= Minimum Break Strength / Safety Factor
STANDARD LENGTH:600 ft
FABRICATION SERVICES:Fabricated Units can be provides including splices, thimbles, integral chafe sleeves, etc. Contact Us for details.
PART NUMBER SERIES:2530 - white
253x - fleck colors
252x - solid colors
PRODUCTS CATALOG INFO NEWS SUPPLIERS CONTACT HOME
262 SW 33rd Street Fort Lauderdale FL 33315 Tel 888-596-7673 Tel (954) 525-6575 Fax (954) 525-5887