Rope Inc. rope and wire
For All Cordage and Wire Needs
BRAIDED
ROPE

Identify Rope Quality

 
Braided Rope How to identify quality in braided rope,
or, get what you pay for!
 
 
 
Sighting the braid
    When selecting a new piece of line, simply sight down its length as you would a plank. If you see broken yarn filaments, high or low strands, corkscrew or roll, randomly uneven yarn color or looped strands; beware!

Broken yarn filaments
    This indicates the use of poorly maintained machinery or lack of yarn finish. This defect will result in lower strength (because a portion of the rope is already broken), greater stretch, premature wear and more rapid degradation.

High or low strands
    The presence of this defect reveals uneven yarn tensioning in manufacture or use of different yarn sizes. It means that some of the yarns will not be sharing the work equally with the others' resulting in more stretch at a given load, lower ultimate break strength and more rapid wear.

Looped strands
    This defect is usually caused by unequal yarn tensioning in the manufacturing process and results in the same problems as mentioned above.

Corkscrew or roll
    This occurs when the tensions of the yarn in one direction are different from the tensions of the yarn in the other direction. It can also be caused by the use of dissimilar yarns, which have differing shrink or stretch characteristics. One major problem with the presence of this defect is that the line may tend to accept of resist (depending on the direction of the roll) the temporary twist, which is induced in sheets when they are peeled from the top of a winch. If the line doesn't properly accept twist in this application it will tend to hockle and jam in blocks more frequently.

Randomly uneven yarn color or sheen
    This is a dead give-away to the use of inferior, odd lot yarns of various types and finished that are likely to result in a variety of problems including uneven wear and premature failure.

Strand twist
    All braided ropes should be constructed using clockwise and counter-clockwise twisted strands (referred to as “S” twist and “Z” twist in the trade). The reason for this design is to orient all of the fine yarn filaments parallel to the longitudinal axis of the rope allowing them to be combed rather than plucked, snagged and broken when dragged over a rough surface as they would be if they were at an angle or perpendicular to the axis of the rope.

Finished yarns
    Raw yarn can be purchased from a producer with “finish or, for a little less cost, without a “finish”. Finish is the trade name for lubricant that is etched or chemically bonded to the yarn, which dramatically improves its performance. The wet performance of a rope made with Seaguard® finish, for example, can out perform an unfinished rope by as much as 20 times.

Properly sized rope
    It is important for a rope to maintain the proper size while under load. Undersized rope presents less surface area to winch and sheave surfaces thereby requiring less yarn to bear more load. Undersized rope may require more wraps to develop the same holding power on a winch. This is especially true when the rope is wet or used in self-tailers. Undersize rope may perform poorly in various cam cleats and halyard stoppers. Check the weight per foot specifications to compare sizes of ropes made with similar materials.

Spliceability
    It is sometimes difficult for the layperson and experienced rigger alike to determine if a rope will be properly spliceable without actually performing the task. A high quality rope is engineered to accomplish a balance of purpose between the double braided cover and core, resulting in uniform spliceability whether the rope is new or used. One simple test, which may indicate an imbalance between cover and core, is to coil the rope. If it does not coil uniformly, bends more sharply in some places or resists coiling altogether, you should question the rope's quality.

Braider splices
    Some manufacturers use undersize braiders to produce rope. While smaller braiders may run faster and are less expensive to buy, rope produced on them will contain many yarn and strand splices in a given length. Splices can sometimes be seen in the cover strands, but are hidden in the core. Premium quality rope, like Yale Cordage, New England Rope, and Samson do not allow braider splices in the core or cover of 600-foot spools.

Cleanliness
    There is no reason to accept rope from a manufacturer with grease or oil spots. While it may no seriously affect performance, it is an indication of lack of commitment of quality and inspection.

Value
    The rope suppliers Rope inc. purchases rope from are committed to providing the highest quality rope products available designed to deliver maximum performance and durability.

® Seaguard is a registered trademark of Allied Fibers

Yale Cordage
This information was taken from a bulletin
supplied by Yale Cordage, Biddeford, Maine

 
 
     Our skilled staff at Rope inc. can provide braided rope for dock lines, running rigging and more. Contact Us for more information.
 
Search this Site!

PRODUCTS CATALOG INFO NEWS SUPPLIERS CONTACT EMAIL HOME

Rope inc.
262 SW 33rd Street
Fort Lauderdale FL  33315
Tel 888-596-7673
Tel (954) 525-6575
Fax (954) 525-5887